• Fully insulated gloves test stamped for working voltages 7500V AC
• Gloves are tested and certified to EN 60903 and IEC 60903
• The EN/IEC 60903 standards advise visual inspection by inflation of the glove in order to detect air leaks. This can be carried out by the pneumatic glove tester
• These gloves must be used with leather over gloves, to ensure protection against damage.
• We would also recommend using these with cotton under gloves for extra cleanliness.
• Thickness : 1.5mm
• Length: 360mm
• Sizes 7,8,9,10,11 available

Mechanical requirements :
– Tensile strength > 16 Mpa
– Puncture resistance > 18 N/mm
– Elongation at break > 600 %
– Tension set

AGEING REQUIREMENTS :
Conditioning of the gloves in an air oven at 70 ± 2 °C during 168 hours :
– The tensile strength and the elongation at break must be at least equal to 80% of non-conditioning gloves. The tension set must not exceed 15%.
– Gloves must pass the proof test voltage and the withstand test voltage.

THERMAL TESTS :
· RESISTANCE TO LOW TEMPERATURE :
Conditioning of gloves for 1 hour at -25 ± 3°C. Tests are satisfactory if no tearing, breaking or cracking after folding is
visible on the cuff and if the gloves pass the proof test voltage and the withstand test voltage.

· FLAME RETARDANCY TEST :
Application of a flame at a finger tips for 10 seconds. Test is satisfactory if, after 55 seconds, the flame has not reached the
marker located 55 mm away at the other end.

SPECIAL PROPERTIES
· CATEGORY H (oil resistance)
Conditioning of gloves by immersion for 24 hr in oil (liquid 102) at 70 ± 2 °C:
Proof and withstand test voltage
Mechanical resistance : > 50% of non conditioning gloves
· CATEGORY A (resistance to acid)
Conditioning of gloves by immersion for 8 hr in sulphuric acid solution (32° Be) heated at 23 ± 2 °C:
Proof and withstand test voltage
Mechanical resistance : > 75% of non conditioning gloves
· CATEGORY Z (resistance to ozone)
Conditioning of gloves for 3 hr in a chamber at 40 ± 2 °C and in a 1 ± 0.01 mg/m3 ozone concentration
Visual control
Proof and withstand test voltage
· CATEGORY C : (resistance to very low temperatures)
Conditioning of gloves for 24 hr at -40 ± 3 °C. and then shall be folded at the wrist in order to be placed between two
polyethylene plate and being subjected to a force of 100 N for 30 seconds :
Visual control
Proof and withstand test voltage
· CATEGORY R = A + Z + H

PACKING :
Each pair of gloves is packaged in an opaque sachet with a direction of use inside. On the packaging, the following information is given : class, size, categories, type of cuff, length of gloves, test date, manufacture and validation batch numbers. The sachet and instruction for use are certified as part of the PPE and must be kept with the gloves.

Data Sheet

Click the thumbnail below to download the data sheet.

The post Class 1 Electrical Safety Gloves appeared first on EINTAC.

• Max working voltage- 1000V DC 1500V AC (Class 0)
• Length 360mm
• Thickness 1mm
• Gloves are tested and certified to EN 60903 and IEC 60903 PPE Category III (Directive 89/686/EEC) IEC 61482-1-2 ASTM F2675
• Available in sizes 8 to 11

Natural latex gloves with outer coating in orange, natural beige interior. Gloves have reinforced mechanical protection & arc flash.

Designed to match hand shape and provide better handling of tools and control devices DEXTERI + WELLFIT is soft to the touch and very supple.

Outer coating provides exceptional grip, even in humid or greasy conditions.

Replace cotton gloves regularly for hygienic reasons. See cotton under-gloves by clicking here.

Class 00 to Class 4 available.

6 months compulsory testing. Tests should include air inflation to check for leaks – please see our pneumatic glove tester, a visual inspection while pressurized and a dielectric test in accordance with EN60903 standards of live working gloves of insulating material.

STORAGE
The gloves must be kept in their original wrapping. Do not compress them. Do not fold them. Do not store them near light or heat sources natural or artificial . Storage temperature must be between 10 and 21° C. Humidity 60+/- 10%

TRANSPORT
Transport conditions must be the same as storage conditions

PRECAUTIONS
Gloves should now be allowed unnecessarily to come in contact with turpentine, white spirit, strong acid or any corrosive products. Do not use wet gloves

USE
Inflate the gloves with air in order to detect potential faults. Carry out visual inspection. The standards EN 60903 and IEC 60903 indicate in annex E.3 (informative) that Category C should be used in ambient temperatures between -40° C and +55° C

CLEANING
With water and soft soap only . Dry at less than 65° C.

PACKING :
Each pair of gloves is packaged in an opaque sachet with a direction of use inside. On the packaging, the following information is given : class, size, categories, type of cuff, length of gloves, test date, manufacture and validation batch numbers. The sachet and instruction for use are certified as part of the PPE and must be kept with the gloves.

The post Class 0 Electrical/Mechanical Insulating Gloves appeared first on EINTAC.

Glove Kit – work safely on any electric or hybrid vehicle with this essential glove kit.

Kit Contents:

• Pack of 10 Cotton Under-Gloves
• Pair of Cat 0 Electrical Safety Gloves
• Leather Over-Gloves
• Glove Storage Bag

If you require a different class rating of gloves or glove sizes, please get in contact and we can arrange this for you.

Check out our blog here to see why wearing 3 pairs of gloves is necessary.

Click here to purchase this product from our USA distributor – Total Lockout

Data sheet

Click on the thumbnail below to download the datasheet.

The post EV Glove Kit appeared first on EINTAC.

• Clear Plastic
• Prevents damage to gloves
• 370 x 170 x 50mm

The post Glove Storage Box – Clear appeared first on EINTAC.

Cat 00 Electrical Safety Gloves

• Fully insulated gloves test stamped for working voltages 500V AC max.
• Thickness: 1mm
• Length: 360mm
• Sizes 8, 9, 10, 11 available
• The EN/IEC 60903 standards advise the visual inspection by inflation of the glove in order to detect air leaks. This can be carried out using the pneumatic glove tester.

Data Sheet

Click the thumbnail below to download the datasheet.

The post Class 00 Electrical Safety Gloves appeared first on EINTAC.

Cotton Under-Gloves act as an extra layer of safety when working on electric and hybrid vehicles.
Worn underneath electrical safety gloves and leather gloves, they give excellent comfort and protection in warm and humid conditions.

• Soft polycotton material offers comfort and protection
• Die cut to ensure consistency of size
• Knitted wrist for a secure fit
• One size fits all
• CE Marked PPE Cat 1 Minimal Risk
• Sold in packs of 10

The post Cotton Undergloves appeared first on EINTAC.

• Fully insulated gloves test stamped for working voltages 1000V AC / 1500V DC
• The EN/IEC 60903 standards advise a visual inspection by inflation of the glove in order to detect air leaks. This can be carried out by the pneumatic glove tester
• These gloves must be used with leather over gloves, to ensure protection against damage.
• We would also recommend using these with cotton under gloves for extra cleanliness
• Material: Natural Latex
• Supplied in an individual UV-resistant bag
• CATEGORY RC = A + Z + C + H
  (resistant to acid, oil-resistant, ozone, and very low temperatures)
• Thickness: 1mm
• Length: 360mm
• Sizes 8,9,10,11 available
• Note: Neutral or Red gloves may be issued

Data Sheet

Click the thumbnail below to download the datasheet.

The post Class 0 Electrical Safety Gloves appeared first on EINTAC.

• Worn over insulating gloves to protect against mechanical hazards and electrical arcing (Class 00 to Class 4)
• Resistant to flame and contact heat of 100°C for 10 seconds in according to EN 407.
• Velcro at the cuff adjusts the tightness of the glove to the user’s hand.
• Silicone goat grain leather, Kevlar® thread stitching.
• Adjustable width by fireproof Velcro strap mounted on leather.
• Complies with standard EN 388: 2016 2122X, EN 407: 2004 412X4X
• Level of dexterity according to EN 420 A1 : 5 (excellent grip)

Size Guide

Measure the circumference of your dominant hand just below your knuckles. Compare the measurements to the size chart below to find your glove size. The size measurements are in inches and relate directly to the glove size. Please note we do advise Cotton Under Gloves to be worn under the Rubber Insulated Gloves, so you need to make a small allowance for that when deciding on glove size.

Data Sheet

Click the thumbnail below to download the datasheet.

The post Premium Leather Overgloves appeared first on EINTAC.

• Carry bag accessory for the insulating gloves, to protect them from damage and for ease of transport
• Has a useful hook
• Internal pocket for talc container (talc not included)
• Will hold 1 pair of electrical gloves
• Dimensions: 450 x 180 x 70 mm
• Material: Reinforced Fabric with waterproof PVC

The post Glove Storage Bag appeared first on EINTAC.